China Plastic Edge Protection for SaleChina Pvc Plastic Cabinet T-Molding Furniture EdgingChina PVC/PP/PE/TPR TPE Tablet Plastic Rubber Corner GuardsChina Roller Shutter Cupboard Doors for SaleChina Roller Shutter Doors Of Kitchen Cabinet ManufacturersWholesale PVC/ABS Plastic Shutter Doors For Cabinets Factory
This video is about how to modify and install and adjust a cheap gimbal with a BCG control board onto a DJI Phantom with Naza-M controller, and a gimbal control lever on the remote control.
The gimbal was designed for a GoPro 2 with SD card access on the right. The GoPro Hero 3 has the SD card on the left. I switched the gimbal arm around to the other side to gain access to the card slot, when the camera is mounted.
I have connected a yellow wire to F1 for the roll control
and a green wire to F2 for the pitch control.
If we power the gimbal from the same battery, that is connected to the Naza controller, then there is no need to connect ground and power to the signal connectors.
The gimbal power and the gimbal control wires are routed
through this hole in the landing gear.
I had to use the orange colored anti-vibration dampeners, because I lost the original black dampeners during a crash.vWe need to be careful to not damage them.
I modified a chop stick from the Chinese restaurant to make my own tool for this task. Make sure the tool you use does not have sharp edges. As an alternative you can use this method here: https://youtu.be/t5ZyTkQisOs
Because I lost a few during a crash, I now use cable ties to secure the dampener.
You may notice, that I modified the camera arm. I did this, because I use a GoPro 3, and I want access to the USB connector at all times. I had to grind off some aluminum to make sure the Velcro strap fits. And I moved the sensor to the left. I covered the sensor board in silicone to protect it from water.
After we install the DJI and BGC software, we connect one USB to the DJI and one USB to the BGC board.
In the Naza Assistant we turn the gimbal control on, and set everything to default settings.
In the BGC software we adjust the pivot and roll limits,
and we calibrate the gimbal sensors. I show all that in the video.
I know this video is long, but it took longer to make it, and I explain everything in great detail.
Good luck, and I hope you enjoy watching this video.
Don’t forget to rate – comment – and subscribe, if you can.
Buy for example at Amazon.com – search for brushless-camera-gimbal with motor and controller for DJI Phantom F450 F550 X525 GoPro Hero3
DJI Phantom Software available at
Controller board software at
I added this (http://youtu.be/Q1-T42o5_10) video, where I explain how to test the gimbal pitch control with DJI and BGC software. At this point I see, that there are issues with Phantom 2 and a non activated Gimbal switch.
Roofing Sheet Roll Forming Machine, Roof Sheet Roll Forming Machine, Roof Panel Roll Forming Machine, Roof Roll Forming Machine, Metal Roof Roll Forming Machine, Roof Tile Roll Forming Machine, Trapezoidal Sheet Roll Forming Machine, IBR Sheet Roll Forming Machine, Produced by Wuxi Techwell Machinery Co.,Ltd. ( Website: www.wxtechwell.com / www.cold-rollformingmachine.com )
Wuxi Techwell Machinery Co.,Ltd is a professional manufacturer specializing in the developing and exporting of cold roll forming machines and insulated sandwich panel machines and Slitting cutting machines.
Roll Forming Machines: Metal roof & wall panel roll forming machine, steel tile roll forming machine, dual level roll forming machine, C/Z/U/L shaped steel roll forming machine, drywall stud and track roll forming machine, steel floor deck roll forming machine, highway guardrail roll froming machinem downspout roll forming machine, rainwater gutter roll forming machine, portable downspout / gutter machines, door frame roll forming machine, roller shutter door roll forming machine, no-girder k span arched panel roll forming machine, slitting & cutting, roof curving machine, stacker machine and so on.
Insulated Sandwich Panel Machines: PU sandwich panel machine, rubber belt pu sandwich panel machine, continuous pu sandwich panel machine, EPS sandwich panel machine, rockwool sandwich panel machine, eps & rockwool sandwich panel machine, mineral wool sandwich panel machine and so on.
Wuxi Techwell engaged in the steel structure industry in many years and devoted to developing some steel structure machines with a professional technology and reasonable price, we supply the best machines for our new and old customers. In paticular, we are a leading exporter in the field of steel structure construction, and can provide professional service, high quality, through design and installation. Our goal is ” Future by heartiness, faith leads to the world”.
Warmly welcome to visit our factory and we are looking forward to cooperating with you for mutual benefits.
Company: Wuxi Techwell Machinery Manufacturing Co.,Ltd
Contact Person: Monica Lee