China Hydroponic Gutter System ExporterEdge Guard for SaleRubber Sealing Strip SupplierWholesale Rubber Strip Seals PricelistWholesale U Shaped Edge Strip FactoriesWholesale Wear Strip Factory
Our company introduction:-
We are DHRUVANSHI GROUP . as a professional manufacturer & import of ROLL FORMING MACHINE. We use AUTO CAD design software. With more than 10 years of experience and strict quality control, our products meet International Standard. We are the leading manufacturer of roll forming machine in China.
We manufacture various kinds of roll forming machines for producing such products as Roof Tile, Wall Panel, Roofing Corrugated Sheet, Floor Deck, C & Z Purling, Highway Guardrail, Sandwich Panel, Container Board, Car Panel, Roll Shutter Door, Downspout, Decorated gusset, Steel Pipe, H-BEAM Line etc.
Our machinery are too much helpful for Sheet Metal Work, Cutting industries of metal sheet, PCB, PVC, Electrical & transformer stamping and manufacturers of Cupboard, Panel board, Steel Furniture, Tin, Drum, Bucket, Tube-light patty and Auto Motor body builders etc.
All Our clients are satisfied with the workmanship and performance of our machines as because our company is accompanied with sound infrastructure and qualified team. Our company prime mission is to provide superior quality industrial machines that are efficient, highly productive and durable
We hereby Sending You Our Company Videos Link where You can See Our Company profile in detail.
309, 3rd Floor Royal Arcade,
Near Jeevandhara Hotel, Varachha Road
Surat – 395006, Gujarat, INDIA
Phone: +91 261 4006868
WHatsApp: +91 99788 31119
http://ali.pub/e09is – Water Pumps from 1.35 $
How to make a #waterpump with their own hands at home. #diy #Homemade #water #pump from scrap materials.
For this we need:
1. Plastic jars with lids – 2 pcs.
2. Syringes – 2 pcs.
3. Engine 12 volts
4. Superglue + hotmelt
1. Cut out the cover in the center of the circle and make a hole equal to the diameter of the motor shaft. In my case, 3 mm.
2. Cut blade impeller. (I made the blade is too wide, it is better to make them smaller (5-7 mm). Stick to the disk.
PS Ring on the blades serve to increase the stiffness, but it was odd.
3. Cut off the bottom of the cans (It will be part of the pump casing. The size depends on the height of the impeller. There must be a reserve of a few millimeters) and make 2 holes. One side angle equal to the inner diameter of the syringe (By the rotational direction of the blades). In my case, 10 mm (12 mm syringe). A second hole for the protruding portion of the engine.
4. Cut off the syringe at an angle and then slightly rounded scalpel for a snug fit to the curve of the banks. Stick to the hot melt adhesive. Then superglue to glue engine.
5. In the cover to make a hole for water intake 10 mm and glue gun.
6. On the side to make a cutout for the syringe.
7. drop of superglue to the center of the impeller and fit onto the motor shaft. Drip a little glue for a better setting.
8. On the inside of the lid cause hot melt and stick to the bottom of the jars.
9. Solder the wires to the engine and tie them in a knot.
10. At the bottom of the can do a small hole under the wire and push wire in it.
11. Glue the motor housing to the pump casing, using hot melt glue. Shёv carefully fluff melting for a better seal.
12. Seal the hole exit wire hot glue.
13. The pump is ready. It is safe to lower it into the water and experience the performance. If you do not dangle, then change the polarity.
Cashback 7% Aliexpress: https://cashback.epn.bz/?inviter=4087b
Partnership program AliExpress: https://epn.bz/joinus/?inviter=4087b
I share all that I am doing own hands at home. The channel you will see homemade, crafts, repair of equipment, experiments, tests, unpacking and review products from China (Aliexpress), various household manual. I also will share my inventions and interesting ideas to improve and simplify the life (life hacking).
Movies shown on that channel, show the personal experience and are entertaining. For all that you do, you answer yourself. Observe caution and safety rules.
///////////////// SUBSCRIBE \\\\\\\\
********** http://goo.gl/Tp0aX9 ***********
////////////// MY CHANNELS \\\\\\\
https://goo.gl/LWSVj3 – Live Laugh
https://goo.gl/GLJ2hf – Alexander Dikovinniy
https://goo.gl/IlJ8ZE – Dikovinniy World
https://goo.gl/2mqicP – Animals and Fun
**************** PLAYLISTS ****************
goo.gl/lTXljH – Instuctions
goo.gl/Jy8Xjd – Parcels, Reviews, Tests
goo.gl/RtQfXg – Water Device
goo.gl/u4Snhv – Interesting Ideas
goo.gl/LzpXou – Repairs
goo.gl/lzM9Yg – Toyota Camry Gracia
goo.gl/zOHwUB – The use of plastic PET bottles DIY
1 – Real_World
2 – Opening_Night
3 – The composition of “Think Tank” belong to the performer Audionautix. License: Creative Commons Attribution (https://creativecommons.org/licenses/by/4.0/).
4 – Movin
/////////////////= HELP CHANNEL =/////////////////
Webmoney (WMZ-dollars): Z315805724463