China Flexible Plastic T Edge Trim ExporterExtrusion Co-Extrusion Plastic Clear PVC Data Strip China SupplierExtrusion Plastic Protective Corner Guards for SaleKitchen Cupboard Roller Shutter Doors ManufacturerWholesale Flexible Trim Edge With Adhesive Tape ManufacturersWholesale Rubber Sealing T Strip（TPR&PP&PVC&TPE) for Sale
Great Amazon Must Haves for Digital Photographers:
Adobe Photoshop Lightroom 6: http://amzn.to/1XhdDsk
Professional Cleaning Set for DSLR Cameras: http://amzn.to/1L5NuU1
Think Tank DSLR Battery Holder: http://amzn.to/1IKmh7J
Joby GP8-BHEN GorillaPod Focus with Ballhead X bundle: http://amzn.to/1LV3RIK
Case Logic SLRC-206 SLR Camera Backpack: http://amzn.to/1fVAyHE
Transcend USB 3.0 Super Speed Multi-Card Reader: http://amzn.to/1EzCmSf
Watch more Photography Tips & Techniques videos: http://www.howcast.com/videos/160199-How-to-Make-a-Pinhole-Camera
In the age of digital cameras and instant gratification, make the simplest camera ever invented using just a light proof box, a hole, and paper.
Step 1: Clean the box
Clean out the inside of the oatmeal box, making sure no oatmeal dust or oats are left inside.
Step 2: Remove top and bottom
Remove the plastic top and bottom from the oatmeal box.
Step 3: Glue the bottom
Add a bead of white glue around the lip of the bottom and reattach it. This will ensure no light comes in through the seam.
Step 4: Paint it black
Spray paint the inside of the oatmeal box with black paint and let dry. Repeat if necessary. Also spray paint the bottom. Let it dry.
Step 5: Paint the top
While the top is off, add contact paper to the box top, then spray paint it black. Make sure it will still fit on the box.
Step 6: Cut a door
Use the craft knife to cut a 3-sided rectangle—a long door—about 1.5 inches wide and half an inch tall into the side of the box.
Make sure the rectangle is roughly centered and parallel to the bottom of the container.
Step 7: Cut a square
Cut a 2.5-inch square out of heavy aluminum foil.
For something sturdier, you can cut the square from the side of the soda can. But be careful, the edges will be extremely sharp.
Step 8: Poke a hole
Using the No. 16 needle, carefully poke a hole into the center of your aluminum square—then sand the hole on both sides with the sandpaper to remove any burrs.
Step 9: Poke it again
Re-drill the same hole, and re-sand it a second time.
Be careful not to touch the hole with your fingers, as natural oils from your skin can clog the hole.
Step 10: Glue the plate
Dab a little epoxy on the edges of pinhole plate with a cotton swab, making sure not to come anywhere close to the pinhole, and place the plate on the inside the oatmeal box, with the pinhole centered in the rectangle you cut earlier.
Step 11: Tape the plate
Add a strip of electrical tape on all sides of the plate to further secure it into place. This will also help it from sliding as the epoxy dries.
Step 12: Make a latch
Add a small piece of tape to the outside of the small door that can keep it closed, then put on the box top.
Step 13: Load the camera
When you’re ready to load your pinhole camera for a shoot, take it into a completely dark room. While in the dark, remove the photo emulsion paper from it’s wrapping, and place it inside the pinhole camera, curved around the edge, emulsion-side facing the pinhole.
Step 14: Close the camera
Close up the box tightly, making sure no light can get in.
Step 15: Take your shot
To shoot a scene, point the doorway toward your subject and open the door for about a 20-second exposure.
Step 16: Remove paper
After you’ve taken your shot, return to a dark room and remove the paper, making sure to put it back in the lightproof bag it came in.
Step 17: Develop your film
Either develop the photo yourself in a darkroom, or take your paper your local high-end camera shop to develop it for you.
Step 18: Eat your oatmeal
Don’t forget to eat your oatmeal.
Did You Know?
The Chinese mentioned pinhole cameras as far back as 500 B.C.