China Self Adhesive Rubber Seal ExporterChina U Shaped Edge Strip ManufacturerElectrical Flexible Large Plastic Trunks China SupplierKitchen Cabinet Roller Shutter Suppliers for SaleRoller Shutter Door Filing Cabinet China FactoryWholesale Pvc Hydroponic System Manufacturers
WPC in any field can be used in wood processing
The resour come from:http://woodplasticdeck.com
WPC flexible, can be applied to any field of wood processing, it is to replace the wood of the best eco-friendly materials, which is the most widely used in wood construction products.
1.Outdoor – outdoor floor,floor corridor, pool edging, open-air corridor.
2.Flower box board – flower boxes, tree pool, fence, trash.
3.Decorative plates – wall decoration panels, sun visors, blinds strip.
4.Bench bar – seat stool, bar chair, back bar, leisure Desktop.
5.Signs – signs, signs, billboards.
6.Structural timber – columns, beams, keel.
7.Hydrophilic plank – plank pier, water channels, construction near water.
8.Profile – plank, trails, deck, handrails, guardrails, fences, partitions, lining profile.
9.Indoor – floor, wall, ceiling, ceiling.
10.Moldings – all kinds of moldings, trim, inserts, trim.
11.Other places – flower corridor, outdoor gazebo, deck, shower panels, door frames sets, acoustic panels, roof.
Here’s a link to a question about the way it works: https://youtu.be/BdI-i38nNY4
We grow peppers and eggplant in these half barrels and it works really well except in the summer when it gets hot and
dry. It takes a long time if you’re running a sprinkler to get these things to get enough water and because I drilled
drainage holes in the bottom, I should have what time about 4 inches from the bottom on the side of barrel, I’ve
mentioned that before.
So I was looking different watering systems and Donald over on webcajun video on how he waters his plants using a
piece of PVC pipe and he mentioned he got the idea from a guy named Jeff over at Bologna ringRanch and I watched both
videos and this is my my version for watering these half barrels.
First remove the cap from a 2 liter soda bottle then take a flat screwdriver and stick under the collar that remains
on the bottleneck and twist it till it snaps off. Then take the soda bottle stick it upside down in a vice and take a
2 inch hole saw and cut a hole in the bottom, start with the side going forward until the drill bit goes through the
bottle and then put it in reverse to finish the whole.
Take some 1 inch PVC and cut it into 12 inch long pieces, stick one end of it in the vice, then take a heat gun and
shoot it down through the center of the pipe. I’m going to let the video run here in full time because it doesn’t take
that long to soften the pipe, just so you get an idea of how long it takes to soften the pipe with the heat gun on
high. When a pipe is soft enough use two hands push down firmly on the bottle and screw the bottle into the pipe until
the whole neck of the bottle is seated in the pipe and then let it cool.
You can’t push on the bottle to put these into the dirt it will either crush the bottle or separate it from the pipe
so take another piece of pipe make a hole part of the distance you want the thing in the dirt, if you want it 9 inches
on the ground push a piece of pipe 6 inches into the ground first then insert the bottle and take the other piece of
pipe slide it inside the bottle and use that to push it 3 more inches into the dirt and then fill it with water.
The first time I used them about a third to about a quarter of the water drained out between a half an hour and an
hour it took over night for the rest of the water to drain out of the bottles.
I don’t know how they’d work just stuck into the ground in a regular garden but it might be worth a shot to try one
and if you let me know how it works out for you.
Well I hope this works for you so far I like it and if you like it please comment, rate and subscribe thanks for