PE/TPE/TPR/PP/PVC Plastic Edge Trim PricelistWholesale PVC Slat wall Panel ExporterWholesale Pvc Slat Wall Panel FactoriesWholesale TPE/PE Wear Strips For Food Machine Parts PricelistWholesale Wall Corner Guards ExporterWholesale Windproof/Soundproof/Waterproof/Fireproof Rubber Seal Strip Factories
[http://www.indiamart.com/aditya-solutions/ ] Aditya Solutions is a sole proprietorship based business venture, which was established in the year 2006 at Hyderabad, Andhra Pradesh. We are counted amongst the renowned manufacturer, supplier and exporter of a wide range of Fly Killer Machines, Hand Dryers, PVC Curtains, Stainless Steel Dustbins and various others. Our product range is designed and developed in compliance with prescribed industrial guidelines by our experienced professionals. These products are highly admired and demanded by clients belonging from different industrial backgrounds for their superb quality standards and some exceptional features such as smooth operations, long service life, less maintenance, easy installations, dimensional accuracy, sturdy construction, high strength, precise designs and anti-corrosive finish. The vast array of products manufactured and supplied by us comprises Shoe Polish Machines, Sensor Dustbins, Fly Killer Machines, Aerosol Dispensers, Paper Dispensers, Hand Dryers, Automatic Hand Dryers, Soap Dispensers, Air Blowers, PVC Plastic Strips, Anti Insect PVC Strips, PVC Air Curtains and many more.
Check out our blog for clickable links to the items below!
Things you will need:
- Stock tank (size of your choosing- ours is 8 ft.)
- Above Ground Pool Pump
- Weatherproof Silicone Sealant
- Hole Saw with Arbor
- Plunger Valves
- Pool Outlet
- 1-3 Rubber Washers (or Gaskets)
- 1 Strainer Nut
Other things you will need for maintenance:
- Chlorine Tablets
- Floating Pool Dispenser
- Water Testing Kit
Step 1- Find a nice level area to lay the stock tank on. If the area where you have chosen isn’t level, use sand or rocks to build up whatever side needs it. It is very important that your stock tank be level so there aren’t any unexpected leaks.
Step 2- Cut holes in your stock tank. I’m not going to lie- this is a pain in the butt. We bought a hole saw with an arbor and it took two people to get through the metal. You will need two holes, one at the top and one at the bottom. In an above ground pool, these aren’t usually right on top of each other, but ours are. We haven’t ever seen this as a problem.
Step 3- Start assembling the parts. In the pool pump package there is a packet with instructions, warnings and troubleshooting. This packet proved to be vital in the setup of the pool. I did end up getting 2 gaskets for the bottom section (the drain section), one for the inside of the pool and one for the outside. It only says you need one for the inside, but this was causing a drip for us. I also put thread seal tape around the connections that were closest to the pool. There are a lot of connections, and each one has a gasket, so you could probably get away without the tape. I didn’t put it on all the connections, the only ones that really seemed to matter were the ones that are connecting the hoses to the pool.
Step 4- Apply silicone waterproof sealant around all crevices involving the input and output parts. I did this on the inside of the pool and the outside. And I applied it VERY HEAVILY and did two layers, allowing one to dry before the second was applied. Sealing these crevices is one of the most important parts. This is what is going to keep the water in the pool. Well all of these steps are leading up to keeping water in the pool, but if there is any chance that it’s going to be getting out, this is what will save you.
Step 5- Test for leaks. Before I added water to the pool, I took a water bottle and poured a good amount of water on the input and output parts. You could also just use a water hose. I would make sure the hose wasn’t on full blast. You don’t want to accidentally penetrate the sealant.
Step 6- Once you are sure there aren’t any leaks, fill the pool just above the bottom hole/output. Check again to see if any leaks have started. If there aren’t any, fill the rest of the pool up!
Step 7- Turn the pump on. Make sure both plunger valves are open/unlocked. When you first do this water may not come out of the output, but there is a solution! Twist off the knob on top of the filter pump to let some air out. Some water may escape too and that’s okay, just be ready to screw it back on as soon as the water starts coming out.